i like this post (click again to cancel)
1
i dont like this post (click again to cancel) remove favorite mark from this question (click again to restore mark)

How do you evaluate protein samples for the feasibility to solve 3D structure?

For example if you record a test HSQC set for a liquid state sample - what basic experimental parameters do you use and what S/N do you expect for a single peak?

What percentage of residues to you expect to be accounted for in the HSQC spectrum? Any other considerations?

Do you have a quantitative test?

asked Jul 20 '10 at 11:47

Evgeny%20Fadeev's gravatar image

Evgeny Fadeev
5771

updated Jul 20 '10 at 20:13


2 Answers:
i like this answer (click again to cancel)
2
i dont like this answer (click again to cancel)

I suppose the following links from the NESG NMR WIKI (1)and (2) will be of help. Considering that we are using a high field cryoprobe equipped NMR spectrometer to record a high resolution 2D-[15N,1H] HSQC (tmax 15N ~ 110ms) spectrum, a signal to noise of 100:1 would mean rapid data acquisition methods (RD/GFT types) could be implemented, while 30:1 would mean conventional methods have to be employed.

The percentage of residues that appear in the HSQC (peak yield = 100*number of peaks observed/number of peaks expected) is a good measure of how well behaved the system is and the feasibility of structure determination could also be judged. A peak yield of >95% is good, while a challenging target might give around 80-85% (not very sure about this). If peak yield of more than 100% is obtained then either the possibility of the protein having more than one conformation is high, or it could be a dimer under the given set of conditions (could be verified by determining the rotational correlation time of the protein from relaxation measurements)

The peak dispersion would give a fair idea of whether the protein is unfolded or folded, if folded whether its a beta-rich or an alpha-rich protein. A good peak dispersion would mean that the protein is largely a beta-sheet rich protein, while a lower dispersion (with a good peak yield) would mean its a alpha-helix rich protein. A poor dispersion coupled with a poor peak yield implies unfolded proteins. I would like to add a note that, this is in reference to water soluble protein - the game with membrane proteins is quiet different.

Hope this helps!

link

answered Jul 21 '10 at 06:34

Bharathwaj's gravatar image

Bharathwaj
112

i like this answer (click again to cancel)
1
i dont like this answer (click again to cancel)

According to my experience, I won't solely rely on the quality of HSQCs to test the feasibility of structure determeination. Of course, getting a high quality HSQC is a necessary condition. But, that is not the sufficient condition. I would rather record 3D-HNCO, 3D-HNCACB & 3D-CBCACONH. These experiments will tell you whether you have to go for "per deuterated sample" or not. In the past, in two cases, I got very good HSQCs. But, when I went for 3D experiments it was total failure. Those were 27 kDa & 28 kDa proteins. So, I had to go for perdeuteration and run TROSY based experiments to complete the backbone assignments. Downside with this is that you have to have a double labeled sample.

So, in short if you don't get a good HSQC - I won't go for double labeling. If I get a good HSQC, I'll keep my fingers crossed till I get good 3D-data using my double labeled sample.

-Ilango.

link

answered Jul 21 '10 at 12:35

Ilango's gravatar image

Ilango
171

Your answer
Please start posting your answer anonymously - your answer will be saved within the current session and published after you log in or create a new account. Please try to give a good answer, for discussions, please use comments and please do remember to vote (login to vote)
toggle preview

powered by CNPROG